Undead Skin

1. Basecoat with 2:1 Rakarth Flesh and Pallid Wych Flesh /.
2. Mix a small amount of Barak-Nar Burgundy into your basecolour and add geral shading to all of the skin. I would recommend thinning this paint with Lahmian Medium , to add transparency and make it easier to layer.
3. Increase the amount of Barak-Nar Burgundy in the mix, so it is roughly 1:1 with the base colour. Now shade the skin again, being more selective. Focus more on recesses and downward facing skin.
4. With a fine line of pure Barak-Nar Burgundy , shade the deepest part of the recess. Rin this around wherever the skin meets other materials.
5. Now is a good time to paint the eyes and a few other key details on the face. I picked out the eyeballs with :Citadel/AverlandSunset, then added a dot of Ice Yellow . Paint inside the mouth with a mix of Black , Barak-Nar Burgundy and Khorne Red . Pick out the teeth with Ushabti Bone and finish with a Wraithbone highlight.
6. Paint inside the mouth with a mix of Black , Barak-Nar Burgundy and Khorne Red .
7. Mix some 1:2 Rakarth Flesh and Pallid Wych Flesh /, so it is slightly lighter than the base mix. No highlight the skin.
8. Selectively highlight with pure Pallid Wych Flesh .
9. Finish with very small/specular White highlights.

I followed these same steps for the green tinged skin. Everything was the same, apart from I used Nocturne Green in the shading, instead of Barak-Nar Burgundy .

White Hair

1. Undercoat: Black
   Basecoat: Corax White & White 1:2
   Shade: Rakarth Flesh & Grey Seer 2:1
   Recess Shade: Stormvermin Fur & Gorthor Brown 1:1
   Glaze: Sotek Green & Fenrisian Grey 1:2
   Highlight: Corax White & White 1:2

Black Hair

1. Basecoat: Black
   Highlight: Kantor Blue and Black 1:1
   Highlight: Thousand Sons Blue & Sybarite 2:1
   Highlight: Fenrisian Grey

Dark Blue Shirt

1. Basecoat: Dark Reaper & Skavenblight Dinge 1:1
   Wash Shade: Abbadon Black & Dark Reaper 1:1
   Edge Highlight: Base Mix & Administratum Grey 1:1
   Edge Highlight: Base Mix & Administratum Grey 1:2

Grey Trousers

1. Basecoat: Dark Reaper & Administratum Grey 1:3
   Recess Shade: Dark Reaper
   Layer Highlight: Base Mix & White Scar 2:1
   Layer Highlight: Base Mix & White Scar 1:1

Brown Shirt

1. Basecoat with Skrag Brown .
2. Soft shade: Doombull Brown
   Deep shade: Abaddon Black & Word Bearers 1:1
   Highlight: Skrag Brown & Ungor Flesh 1:1
   Highlight: Ungor Flesh
   Highlight: Ushabti Bone

Black Trousers

1. Basecoat with 2:1 :black and Dryad Bark .
2. Shade: Abaddon Black
   Edge highlight: Dryad Bark
   Edge highlight: Stormvermin Fur
   Edge highlight: Stormvermin Fur & Deepkin Flesh 1:1
   Edge highlight: Deepkin Flesh

Wood

1. Basecoat with 1:1 Dryad Bark & Mournfang Brown .
2. Run some thin Dryad Bark into recesses. Don't worry about doing this on woodgrain, just deep recesses and where the wood meats other marterial.
3. Highlight with a 1:1 mix of the base colour & Karak Stone .
4. Selectively highlight with Karak Stone .
5. Optionally, selectively edge highlight with 2:1 Karak Stone & Wraithbone if you want to go the extra mile.

Steel

1. Basecoat with Leadbelcher .
2. Wash with Nuln Oil .
3. Enhance the shading with glazes of Agrax Earthshade . Mixing a little Black in and being more selective with a second pass.
4. Highlight with Ironbreaker .
5. Finish with selective Silver RLM01 Metallic highlights.