How I painted my copy of the official 'Scout' model for the new game 1490 Doom.

Yellow Cloth

1. Basecoat with 1:1 Zamesi Desert and Ice Yellow .
2. Soft shade with thinned Averland Sunset .
3. Shade more precisely with Skrag Brown .
4. In particular deep recesses, consider a small amount of Mournfang Brown .
5. Now mix Zamesi Desert and Ice Yellow again, this time in a 1:2 ratio. Use this mix to apply edge highlights.
6. Finally, mix a little White into the above, and selectively highlight.

Blue-Grey Cloth

1. Basecoat with Dark Reaper .
2. Shade recesses with thinned Corvus Black .
3. Edge highlight folds with 1:1 Dark Reaper and Administratum Grey .
4. Finish with selective edge highlights of Administratum Grey .

Black Leather

1. Basecoat with Black .
2. Apply general highlights of Stegadon Scale Green .
3. Fine edge highlight everything, using Thunderhawk Blue .
4. Selectively highlight corners and curves with Fenrisian Grey .
5. Mix some White into your Fenrisian Grey then add a few specular highlights to corners.

Black Cloth

1. Basecoat with Black .
2. Highlight folds with Eshin Grey .
3. Add fine edge highlights along folds with Dawnstone .
4. Selectively highlight folds with Administratum Grey .

Bindings

1. Basecoat with Steel Legion Drab .
2. Shae between the wrapping with thinned Rhinox Hide and a thin brush.d
3. Glaze raised areas with Karak Stone , dragging your brush upwards.
4. Edge highlight wrappings with Ushabti Bone .
5. More selectively highlight with Screaming Skull .
6. Mix some White into your Screaming Skull and highlight a little smaller.

Skin

1. Basecoat with Cadian Fleshtone .
2. Wash with 2:1 Reikland Fleshshade and Contrast Medium .
3. Selectively highlight with Kislev Flesh .
4. Finish with specular highlights of Pallid Wych Flesh .

Dark Brown Leather

1. Basecoat with Rhinox Hide .
2. Take some thinned Mournfang Brown and apply a heavy glaze over the leather. You are looking to cover pretty much everything but the recesses here.
3. Now with Skrag Brown , apply a chunky highlight down the most exposed parts, covering less area that the previous stage.
4. Mix 1:1 Skrag Brown and Ushabti Bone and repeat the above, but make it a finer highlight.
5. Selectively highlight with Ushabti Bone .
6. Add a little :white to the Ushabti Bone and add a couple of specular highlights, where needed.

Pale Leather Tube

1. Basecoat as Karak Stone .
2. Shade with Baneblade Brown .
3. Deep shade with Dryad Bark . The jump between the initial stage and this is quite big, consider a 1:1 mix of the two to bridge the gap.
4. Apply a chunky highlight of Ushabti Bone . This is best applied as a heavy glaze.
5. Apply smaller highlights with Screaming Skull .
6. I finished of the tubes by mixing a little White into your Screaming Skull and applying a few specular highlights.

Steel

1. Basecoat with Leadbelcher .
2. Wash with Nuln Oil .
3. Glaze some Agrax Earthshade where you want metal to look dirtier.
4. Mix some Silver RLM01 Metallic into your Leadbelcher , then highlight close to the tip (on the flat sides) and edge highlight the rest.
5. With pure Silver RLM01 Metallic , edge highlight the tip and place a few specular highlights on corners.

Brass

1. Basecoat with Runelord Brass .
2. Wash with Reikland Fleshshade .
3. Highlight with Runelord Brass , lightened with a little Silver RLM01 Metallic .
4. Finish with specular highlights of Silver RLM01 Metallic