Weathered Copper

1. I started by priming with Hyrax Brown to speed up the initial basecoat.
2. Thin Sotek Green roughly 1:1 with water, then apply a coat of paint, using a round drybrush. Do this with a whole series of dabs, so it coats all over, but gives uneven coverage.
3. Mix your Sotek Green 1:1 with White , then thin with roughly twice as much water. Use this paint as a wash, and cover all of the bronze.
4. Drybrush all over with Warplock Bronze .
5. Repeat, but with a lighter drybrush of Balthasar Gold . This stage it to lighten the most exposed areas.
6. Mix the Balthasar Gold with a little Silver RLM01 Metallic , then highlight more selectively.
7. Finish with specular highlights of pure Silver RLM01 Metallic .

Chains

1. Basecoat with 1:1 Black and Leadbelcher .
2. Overbrush with Leadbelcher .
3. Wash with Nuln Oil mixed with Agrax Earthshade .
4. Highlight links selectively with with Ironbreaker .
5. Finish with selective Silver RLM01 Metallic highlights.

Steel

1. Basecoat with Leadbelcher .
2. Wash with Nuln Oil . To make it look extra dirty, consider multiple passes or even adding some other browns and oranges to the mix to make the metal look rustier.
3. Highlight with Ironbreaker .
4. Finish with selective Silver RLM01 Metallic highlights.

Pale Skin

1. Basecoat with an equal parts mix of Cadian Fleshtone , Administratum Grey and White .
2. Increase the amount of Cadian Fleshtone in the mix and add shading.
3. Enhance this shading by adding increasing amount of Doombull Brown to the mix, then shading a smaller area. Repeat as necessary.
4. For the highlights, add a little White to your initial base colour and pick out raised areas.
5. Finish with a few small White highlights.

Black Cloth

1. Basecoat with Black .
2. Highlight with Skavenblight Dinge .
3. Highlight more selectively with Stormvermin Fur .
4. Mix a little :white, or any other light colour into your Stormvermin Fur , and add very small/specular highlights.

Sheep

1. Basecoat with Rakarth Flesh .
2. Wash with some very thin Baneblade Brown .
3. Add general shading with some Stormvermin Fur .
4. Enhance the above shading with a smaller amount of Skavenblight Dinge , where needed.
5. Mix your Rakarth Flesh with a little White and highlight.
6. Finish with some very small/specular White highlights.

Cords

1. Basecoat with Steel Legion Drab .
2. Highlight with Karak Stone , covering most of the exposed edge.
3. Mix a little White into the Karak Stone , then add a few dots within the last stages highlight.

Wood

1. Basecoat with Thondia Brown .
2. Shade with thinned Rhinox Hide .
3. Drybrush with Thondia Brown & Steel Legion Drab mixed 2:1.
4. Edge highlight with 1:1 Thondia Brown & Steel Legion Drab .
5. Selectively highlight with the previous colour mixed 1:1 with Administratum Grey .
6. Finish with specular highlights using pure Administratum Grey .

Light Wood Panel

1. Basecoat with Steel Legion Drab
2. Shade the whole panel with a glaze or two of Dryad Bark , pulling your brush towards the bottom.
3. Highlight with Baneblade Brown .
4. Selectively highlight with Ushabti Bone .
5. Mix a little White into your Ushabti Bone and finish with some very small highlights.

Yellow Panel

1. Basecoat with Zamesi Desert .
2. Shade the whole panel with a glaze or two of Skrag Brown , pulling your brush towards the bottom.
3. Highlight with a 1:1 mix of Zamesi Desert and Ice Yellow .
4. Selectively highlight with Ice Yellow .
5. Finish with a few small White highlights.

White Panel

1. Basecoat with 1:1 Deepkin Flesh and Ulthuan Grey .
2. Shade the whole panel with a glaze or two of 1:1 Celestra Grey and Ionrach Skin , pulling your brush towards the bottom.
3. Enhance the shading with Agrax Earthshade . I worked a little on my wet palette and picked out the deepest recesses only.
4. Mix some White into your base colour and highlight.
5. Finish with selective highlights of pure White .

Blue Panel

1. Basecoat with Thunderhawk Blue .
2. Shade with Dark Reaper .

Gold

1. Basecoat with Retributor Armour .
2. Wash with Agrax Earthshade .
3. Mix some Silver RLM01 Metallic into your Retributor Armour and highlight.
4. Finish with very small Silver RLM01 Metallic highlights.

Copper

1. Basecoat with Hashut Copper .
2. Shade with glazes of Gore-grunta Fur .
3. Enhance shading witha more selective application of Doombull Brown and Abaddon Black .
4. Mix your Hashut Copper with Silver RLM01 Metallic and highlight.
5. Finish with selective Silver RLM01 Metallic highlights.