Grey Cloth

1. Basecoat with Stormvermin Fur .
2. Shade with a mix of 2 parts Stormvermin Fur , 2 parts Abaddon Black and 1 part Incubi Darkness .
3. Highlight with 1:1 Stormvermin Fur and Administratum Grey .
4. Highlight more selectively with 1:1 Administratum Grey and White .

Black Cloth

1. Basecoat with 1:1 Black and Naggaroth Night .
2. Shade recesses with Black .
3. Glaze raised areas with the base colour mixed 1:1 with Eshin Grey .
4. Repeat, coverring a smaller area with just Eshin Grey .
5. Apply chunky highlights with Stormvermin Fur . These are best applied with a series of scratchy lines.
6. Mix your Stormvermin Fur 1:1 with Administratum Grey , then add in fine edge highlights.
7. Highlight selectively with pure Administratum Grey .
8. Finish with a few very small highlights of 1:1 Administratum Grey and White .

You could definitely simplify this method and leave out the glazing. However, I wanted an interesting cloak that I could also use on my Chorister too. With there not being much call to use this colour on the troopers, I think it is worth the effort to tie the whole force together.

Gasmask

1. Basecoat with Administratum Grey .
2. Shade with a 1:1 mix of Administratum Grey and Rhinox Hide .
3. Further define deep recesses with some thin Rhinox Hide .
4. Add selective highlights using 1:1 Administratum Grey and White .
5. Finish with a few small White highlights.

Full transparency, these masks are pretty small. So I typically thin my initial shade colour heavily, then apply it as an all over wash. This means you will have to re-establish the Administratum Grey before proceeding with highlights though.

Leg Wrappings

1. Basecoat with 2:1 Wraithbone and Rakarth Flesh .
2. Wash with Agrax Earthshade .
3. Edge highlight with Wraithbone .
4. Selectively edge highlight with 1:1 Wraithbone and White .

Tan leather

1. Basecoat with Steel Legion Drab .
2. Shade with 1:1 Tallarn Sand and Rhinox Hide .
3. Deep shade with Rhinox Hide where needed. I typically just use this colour to separate the boots from the wraps.
4. Highlight with Baneblade Brown .
5. Selectively highlight with Karak Stone .

Black Leather

1. Basecoat with Black .
2. Glaze Incubi Darkness over all the exposed tubing.
3. Apply fine highlights of Incubi Darkness 1:1 with Deepkin Flesh .
4. Add selective highlights of Deepkin Flesh on corners and points that would catch the light.
5. Mix a little Ivory or Pallid Wych Flesh into your Deepkin Flesh and add specular highlights where needed.

Dead Skin

1. Basecoat with an equal parts mix of Cadian Fleshtone , Administratum Grey and White .
2. Take a small portion of the above colour and mix it 1:1 with Doombull Brown . Thin this new colour to a wash consistency with Lahmian Medium and wash the skin.
3. Add a little Naggaroth Night to the previous paint and shade deep recesses that need a little more definition.
4. Re-establish the base colour where needed, before adding a little :white to it and selectively highlighting.
5. Finish off with a few specular White highlights.

Rusted Steel

1. Add patches of Typhus Corrosion , over the primer, in recesses and details where rust would build.
2. Basecoat with 1:1 Thondia Brown and Abaddon Black .
3. Stipple some thin Mournfang Brown in the rusty patches.
4. Repeat with a smaller amounts of Skrag Brown .
5. Edge highlight with Leadbelcher .
6. Finish with selective highlights of Silver RLM01 Metallic .

Steel

1. Basecoat with Leadbelcher .
2. Wash with Nuln Oil .
3. Enhance the shading with glazes of Agrax Earthshade , where you want it to look dirtier.
4. Highlight with Ironbreaker .
5. Finish with selective Silver RLM01 Metallic highlights.