Red Cloak

1. Basecoat with a 1:2 mix of Wazdakka Red & Screamer Pink
2. Add shading to recesses with a mix of Khorne Red & Barak-Nar Burgundy .
3. Add some Abaddon Black to your Khorne Red & Barak-Nar Burgundy mix, then shade more selectively.
4. Make scratchy highlights around the edge of the cloth with 1:1 Wazdakka Red & Morghast Bone .
5. Now highlight again, this time with thinner highlights. I used the previous Wazdakka Red & Morghast Bone mix, with an equal amount of Ushabti Bone added to it.
6. Selectively highlight with pure Ushabti Bone .
7. Finially, mix some White into your Ushabti Bone (roughly 1:1, and add very small/specular highlights.

Steel

Glass Visor

Teal Cloth

1. Basecoat with a 1:1 mix of Dark Reaper & Lupercal Green .
2. Add shading with by adding some black into the base colour, then running it into recesses.
3. Mix a portion of the base colour 1:1 with Sons of Horus Green , then add general highlights to the cloth.
4. Apply fine highlights with pure Sons of Horus Green .
5. With the Sons of Horus Green mixed 1:1 Ionrach Skin , selectively highlight corners and curves.
6. Finish with specular Deepkin Flesh highlights.

Cream Cloth

1. Basecoat with Karak Stone .
2. Thin some Zandri Dust and generously shade the cloth, almost like you would a wash.
3. Shade the recesses further, but more precisely, with Steel Legion Drab .
4. Mix some Rhinox Hide into your Steel Legion Drab then use small amount to shade where the cloth meets other details, harsh folds and in holes.
5. Mix Karak Stone and Screaming Skull 1:1, then add fine highlights to folds and raised details.
6. mix some White into the paint from the previous stage and selectively highlight.
7. Finish with specular highlights of pure White (where needed).

Bandages

1. Basecoat with Steel Legion Drab .
2. Shade between the wrapping with thinned Rhinox Hide and a thin brush.
3. Glaze raised areas with Karak Stone , dragging your brush upwards.
4. Edge highlight wrappings with Ushabti Bone .
5. More selectively highlight with Screaming Skull .
6. Mix some :white into your Screaming Skull and highlight a little smaller.

Grey Cloth

1. Basecoat with Stormvermin Fur .
2. Wash with Nuln Oil .
3. Highlight: Stormvermin Fur+ Administratum Grey
   Highlight: Administratum Grey + White

Skin

1. Basecoat with Cadian Fleshtone .
2. Wash with 2:1 Reikland Fleshshade and Contrast Medium .
3. Selectively highlight with Kislev Flesh .
4. Finish with specular highlights of Pallid Wych Flesh .

Dark Brown Leather

1. Basecoat with Rhinox Hide .
2. Take some thinned Mournfang Brown and apply a heavy glaze over the tube. Work in rough lines, always pulling your brush towards the apex of the tube.
3. Now with Skrag Brown , apply a chunky highlight down the most exposed part of the tube, covering less area that the previous stage.
4. Mix 1:1 Skrag Brown and Ushabti Bone and repeat the above, but make it a finer highlight.
5. Selectively highlight with Ushabti Bone .
6. Add a little White to the Ushabti Bone and add a couple of specular highlights, where needed.

Breathing Tube

1. Basecoat as Karak Stone .
2. Shade with Baneblade Brown .
3. Deep shade with Dryad Bark . The jump between the initial stage and this is quite big, consider a 1:1 mix of the two to bridge the gap.
4. Apply a chunky highlight of Ushabti Bone . This is best applied as a heavy glaze.
5. Apply smaller highlights with Screaming Skull .
6. I finished of the tubes by mixing a little White into your Screaming Skull and applying a few specular highlights.

Leather Air Pouch

1. Basecoat: XV88, Zandri Dust & Doombull Brown 2:2:1
   Soft shade: XV88 & Doombull Brown 1:1
   Deep Shade: XV88 & Rhinox Hide 1:1
   Blend Highlight: Karak Stone & Zandri Dust 1:1
   Highlight: Karak Stone
   Highlight: Wraithbone & Rakarth Flesh 2:1